2N Central Semiconductor Bipolar Transistors – BJT PNP Ampl/Switch datasheet, inventory, & pricing. Data Sheet No. 2N Generic Part Number: 2N REF: MIL-PRF/ Features: • General-purpose transistor for high speed switching and driver. 2N And 2N ARE PNP SMALL SIGNAL GENERAL PURPOSE NJ Semi-Conductors encourages customers to verify that datasheets are current.

Author: Zutilar Vorn
Country: Zambia
Language: English (Spanish)
Genre: Life
Published (Last): 3 March 2012
Pages: 381
PDF File Size: 10.92 Mb
ePub File Size: 20.20 Mb
ISBN: 725-2-91104-621-8
Downloads: 51506
Price: Free* [*Free Regsitration Required]
Uploader: Merg

Use a 2N 2n datasheet instead that has a maximum allowed collector current of mA and its datasheet shows all of them working very well at mA and not too bad at mA. They daatasheet have it top to bottom numbering though.

Datawheet the base resistor value should be 5V — 0. On this topic, ignore the Wikipedia article. Re-drawing their circuit makes it more obvious what is going on.

Still guessing, but to me shorting C-E together in that installation may be for protecting the transistor from damage if a ‘floating lead’ picks ul a harmful voltage, or damage that purportedly can be caused by running a transistkr with too much base current vs collector-emitter current I remember back in my early EE days reading textbooks warning of premature death from oversignalling transistors without enough avail.

This is the current setup two more pairs like this for the other cylinders that 2n datasheet producing weak spark: The chart details the maximum allowable power dissipation with 2n datasheet ambient temperature for a 2N transistor. How to Derate ; Guideline for Derating Components. Mouser Electronics har inaktiverat TLS 1.


Most likely my max load will be ma or under. It would act like a diode. Some suggested transistors are listed below. RobhercKV5ROB This is odd, because this is exactly how BJT switches work; they are deeply saturated, with the base current way higher than minimal current 2n40333 for the required collector current.

The applications section in there is terrific. What would be the rationale for using the C-B junction as well as the E-B junction? The numbering comes from the short circuit protection being an add on datashheet the original external pass transistor circuit, instead from scratch.

Post Your Answer Discard By datashwet “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies. I kind of suspect a diode, but can’t figure out why a plain old diode wouldn’t work better and be a lot cheaper. In this configuration they almost have the same IV curve, but the NPN doesn’t work the same as a diode when in the negative sweep like two back to back diodes would.


Number things left-to-right and top-to-bottom. With this deliberate imbalance, one could argue that the precision of the V BE match is not as important, so a matching transistor at Q2 is not as important, so diode or wrongly connected transistor is not a problem.


Home Questions Tags Users Unanswered. This short circuit protection is added because of the use of an external pass transistor prevents the internal short circuit protection from working.

2N4033 Datasheet PDF

Figure 31 Dztasheet 15 ti. Dave2n datasheet 30, Yes, my password is: If you start 2n datasheet on about page 3 2n datasheet this 2n datasheet Electro Tech is an online community with overmembers who enjoy talking about and building electronic circuits, projects and gadgets. I can’t speak for the real world configuration as I datsheet actually used a transistor like this but it did almost what I thought it would. But not many give practical applications like this power booster. You will see schematics of variations using two BJTs: Voltage divides and current flows top-to-bottom.

C-E current to satisfy gain. Have you any citations or explanation? What role would Q2 play in that configuration?

2N4033 Datasheet

I think they goofed. If you disconnect their collector from emitter and connect it to base, you get a current mirror or current multiplier. Funny, everyone else has the second layout, fairchild, st, onsemi.

Redrawing clarifies simple circuits.