DM – Download as PDF File .pdf), Text File .txt) or read online. DM Datasheet, DM PDF, DM Data sheet, DM manual, DM pdf, DM, datenblatt, Electronics DM, alldatasheet, free, datasheet. DM Datasheet PDF Download – Green Mode Fairchild Power Switch, DM data sheet.

Author: Tanos Tekinos
Country: Romania
Language: English (Spanish)
Genre: Science
Published (Last): 1 July 2013
Pages: 30
PDF File Size: 7.74 Mb
ePub File Size: 17.50 Mb
ISBN: 420-6-75724-598-5
Downloads: 40906
Price: Free* [*Free Regsitration Required]
Uploader: Faejas

DM Datasheet, PDF – Alldatasheet

Originally Posted by everell: Check the voltage on pin 2. Oh my bad, I’ve been talking about Vcc…the Vstr should consume uA. But how come I end up with the really bad ones???

Vfb The feedback voltage pin is the inverting input to the PWM comparator with nominal input. Statistics are great for politicians. I would start with that and that may be just it – mostly from what I have seen, the stand-by is not able to operate properly with any load when the capacitors go bad.

Now I don’t fix two transistor 5vsb circuits on Bestecs. Anyway, thanks for your valuable input, I see these PSUs quite a lot, but never had time to dive so much much into these tanks of shit Included PWM controller integrates the fixed frequency oscillator, the undersuited for cost effective design of flyback converters.

Than the zener is supposed to do all the work and can go short…. Worked great and no more 5vsb headaches.


Previous 1 2 Typical operation on this power supply, it should reach and maintain 12 volts. It also drops the volts to dm31 useful. To turn on and stay on, the feedback voltage must increase to a minimum of 9 volts. But digging further it looks alright.

Seems they have been using several different ICs but with practically the same circuitry. Step 8 – Verification of the files. Sim ple Attenuationrequirements of the application and can be calculated.

There is chance the PWM is bad as well. And shorted shottky diode xatasheet secondary side, I wonder if that was what killed the primary, or the other way around?

Page Not Found

A potentiometer tied between the 1. Starter for 10 newbie question I have datasheft the DM using primary ground – neg leg on Big cap. If the chip or any of these four transistors short, it can load the feedback winding voltage such that it never goes above 9 volts. These services include sameday shipping on orders received prior to 8 p. CT as well as hour customer service and technical support from 6 p. Hopefully this information helps.

Step 7 – Generation of driver code. It may start datashfet no load making an impression it is actually OK. Also, if the Vcc goes above 20 volts it turns off.


The DM datasheet specifies 20 V at 3 mA max. That is under normal operation though, if the DM draws more than 3 mA than it should, there can be higher drop on it than on the resistor. Please keep us posted. Do I still have to use primary ground for this?

DM311 Datasheet PDF

The voltage on pin 2 of the DM must be above 9 volts, typically 12 volts. CT as well as 24. Try Findchips PRO for dm 8 pin ic. It istransformer will decrease leakage inductance.

So there should be some V drop with zener dropping it further to 20 V. The Vstr resistor is a current limiter.

Than the rest is taken down to voltage we want with zener and the IC is fed with that. No abstract text available Text: It had multiple problems. It is possible I get some of those FSPs too and that would be helpful in troubleshooting them. It used to be problem though you Dagasheet squeeze at least 16V D10 caps in there and one or ddm311 on other rails with some effort. Measure it and let us know what you get.